Solos DSL Parameters

Parameter		Description


Version			Traverse firmware build version
DriverVersion		DSL driver version
APIVersion		API version
FirmwareVersion		Firmware version
DspVersion		Internal DSP version

CommonHandshake		Indicates whether Common Handshake Protocol is enabled
			and supported inside DSP or not

Connected		Indicates whether DSL line is in Data mode or not

OperationalMode		Indicates in which mode the line has come up
			T1.413, g.lite, G.Dmt, Multimode,
			ADSL2, ADSL2+, Inactive

State			Indicates the state of the DSL line
			Idle, Showtime, BitSwapping, HandShake, Training, 
			Discovery, Training(DELT), DELT, SpectrumTest

Watchdog		Value of the watchdog timer from DSP
			0x0053 : System is in good health. 
			0X0000 : IPU lock up detected. 
			0XAC : PCU lock up detected

OperationProgress	Indicates the Startup progress while DSL line 
			is coming up

LastFailed		Indicates the reason and stage at which the bring-up of
			DSL line failed last time

TxBitRate		TX bit rate
RxBitRate		RX bit rate

DeltACTATPds		Actual Aggregate Transmit Power for Downstream
			in DELT Mode

DeltACTATPus		Actual Aggregate Transmit Power for Upstream
			in DELT Mode

TxATTNDR		Maximum attainable rate Upstream
RxATTNDR		Maximum attainable rate Downstream

AnnexType		Annex type of line
			AnnexA, AnnexB, AnnexM, AnnexL, Inactive

InterleaveDpDn		Downstream Interleave Depth
InterleaveDpUp		Upstream Interleave Depth
RSCorrectedErrorsDn	Reed Solomon Corrected Errors in Downstream
RSUnCorrectedErrorsDn	Reed Solomon Uncorrected Errors in Downstream
RSCorrectedErrorsUp	Reed Solomon Corrected Errors in Upstream
RSUnCorrectedErrorsUp	Reed Solomon Uncorrected Errors in Upstream

InterleaveRDn		Number of RS redundancy octets per codeword 
			in Downstream in Interleave mode

InterleaveRUp		Number of RS redundancy octets per codeword
			in Upstream in Interleave mode

BisRDn			Number of RS redundancy octets per codeword in
			Downstream

BisRUp			Number of RS redundancy octets per codeword in
			Upstream

INPdown			Number of DMT symbols protected against impulse noise 
			in Downstream

INPup			Number of DMT symbols protected against impulse noise
			in Upstream

ShowtimeStart		Line up time in seconds
ATURVendor		CPE's Vendor ID
ATUCCountry		CO's country
ATURANSIRev		CPE ANSI Revision Number in case of T1.413
ATURANSISTD		CPE ANSI Standard/Version Number in case of T1.413
ATUCANSIRev		CO's ANSI Revision in case of T1.413

ATUCANSIId		CO's ANSI Vendor ID
			BRCM, TXN, ADI, Aware, ST/Alcatel, IFX, Ciena/Catena, 
			CTLM, TexasIns, AlcatelME, AlcatelNtwrkS, Cisco

ATUCANSISTD		CO's ANSI Standard/Version number in case of T1.413
DataBoost		Shows whether Data Boost is to be enabled or not
LocalITUCountryCode	CPE's country code
LocalSEF		Severely Errored Frames count in CPE
LocalEndLOS		Loss of Signal in CPE
LocalSNRMargin		SNR margin in CPE
LocalLineAttn		Downstream line attenuation
LocalTxPower		Upstream Transmit Power
RemoteTxPower		Downstream Transmit Power
RemoteSEF		Severely Errored Frames count received by CO
RemoteLOS		Loss of Signal received by CO
RemoteLineAttn		CO's line attenuation
RemoteSNRMargin		CO's SNR margin

LineUpCount		Number of times the line has come up in SHOWTIME after
			system reboot

SRACnt			Number of downstream SRA's happened on the DSL line
SRACntUp		Number of upstream SRA's happened on the DSL line
ProfileStatus		Indicates the profile selected

Action			Startup
			Startup, DELT, L3REQ, SpectrumReverb, SpectrumMedely, 
			SpectrumPilot, MtsRequest

ActivateLine		Indicates Start/Abort on the line
			None, Abort, Start

LineStatus		Flag indicating if the line was given Abort/Start.  
			It will be false if line is aborted, else true.

HostControl		Enable/Disable Flag to control host

AutoStart		Flag indicating whether the line should be auto started
			or not when the system comes up

Failsafe		Enable or disable the failsafe timer. It is used to 
			re-issue startup if line fails to reach SHOWTIME in 
			some fixed time interval (currently set to 2 mins).

ShowtimeLed		Specify which LED is to be used to display State

Retrain			Option to configure the type of Retrain permissible on 
			line

Defaults		Option to assign defaults to all the parameters

LineMode		Indicates the defaults if any were set using Defaults
			parameter

Profile			Configures the profile to be used
			MAIN, BT, SPAIN, SBC, COVAD, BRAZIL, MII, KT, TELSTRA,
			XR, HAN, FRANCE, FINLAND, FASTWEB, RESERVED

DetectNoise		Enables and Disables Detect Noise

BisAForceSNRMarginDn	Set downstream SNR margin forcefully at the CPE 
			for Bis/Bis+

BisMForceSNRMarginDn	Set downstream SNR margin forcefully at the CPE
			for Bis/Bis+

BisAMaxMargin		Maximum SNR Margin for Bis/Bis+
BisMMaxMargin		Maximum SNR Margin for Bis/Bis+

AnnexAForceSNRMarginDn	Set downstream SNR margin forcefully at the CPE 
			for AnnexA/B

AnnexAMaxMargin		Maximum SNR Margin for Annex A
AnnexMMaxMargin		Maximum SNR Margin for Annex M

SupportedAnnexes	Supported Annexes in the system
			BisA, BisM, AnnexA, T1 413A, BisB, AnnexB, T1 413B

Status			Status of the DSL physical link
			Disabled, NoSignal, Initializing, EstablishingLink, Up

TotalStart		Number of seconds since the beginning of the period 
			used for collection of total statistics

RecentShowtimeStart	Number of seconds since the most recent DSL Showtime
TotalRxBlocks		Total number of successfully received blocks
TotalTxBlocks		Total number of successfully transmitted blocks
